Crystek Corporation

<p>The Crystek CCSMA1-MM-RG174-6 is a 50 Ohm RG174 coaxial cable assembly featuring a straight SMA plug on one end and a right-angle SMA plug on the other. Both connectors are male and free-hanging (in-line). The cable is 6 inches (152.40mm) long and constructed with a 26 AWG bare copper covered steel center conductor, polyethylene insulation, tinned copper braid shield (90% coverage), and a black PVC jacket. The assembly includes a strain relief using adhesive shrink tubing over the crimp area. Operating temperature range is -40°C to +85°C. This shielded cable assembly is suitable for RF interconnections where space constraints benefit from a right-angle connector.</p>

<p>The Crystek CVCO55CC-0775-0800 is a voltage controlled oscillator (VCO) designed for the 775 to 800 MHz frequency range. It operates from a nominal 5.0 V supply (4.75 V to 5.25 V) and draws a typical supply current of 30 mA. The tuning voltage range is 0.3 V to 4.7 V, with a tuning sensitivity of 6 MHz/V.</p><p>&nbsp;</p><p>Output power is typically -5.0 dBm with a minimum of -7.0 dBm and maximum of -3.0 dBm. Harmonic suppression for the 2nd harmonic is typically -15 dBc. Phase noise is -123 dBc/Hz typical at 10 kHz offset and -143 dBc/Hz at 100 kHz offset. The VCO exhibits pushing of 0.2 MHz/V and pulling of 0.1 MHz pk-pk.</p><p>&nbsp;</p><p>The device is housed in a 16-QFN surface mount package measuring 12.70 mm x 12.70 mm x 5.59 mm. It is supplied in tape and reel packaging. Operating temperature range is -30°C to +70°C, with storage from -45°C to +90°C. Load impedance is 50 Ohms, and input capacitance is 47 pF.</p>

<p>The Crystek CVHD-950-122.880 is a 122.88 MHz Voltage Controlled Crystal Oscillator (VCXO) from the CVHD-950 series. It features a CMOS output, 3.3V supply voltage, and an absolute pull range (APR) of ±20ppm minimum. The oscillator is based on a high-Q crystal with third overtone technology, delivering ultra-low phase noise and low jitter performance. Typical phase noise at 100 MHz is -140 dBc/Hz at 1kHz offset, -155 dBc/Hz at 10kHz, -164 dBc/Hz at 100kHz, and -166 dBc/Hz at 1MHz, with a noise floor of -166 dBc/Hz typical. Phase jitter (12kHz to 20MHz) is 40fs typical.</p><p>&nbsp;</p><p>The device operates over a temperature range of 0°C to 70°C with frequency stability of ±20ppm inclusive of calibration, temperature, and aging. It is housed in a 4-SMD, No Lead package measuring 14.20mm x 9.14mm with a seated height of 5.30mm, suitable for surface mount assembly. The oscillator has no sub-harmonics and offers a modulation bandwidth greater than 10kHz at -3dB. Typical applications include high-definition TV, avionics, low phase signal sources, and test and measurement equipment.</p><p>&nbsp;</p><p>Electrical characteristics include a supply current of 15mA typical (25mA max), rise/fall time of 3ns max (20% to 80% Vdd), and output symmetry of 45/55% at 50% Vdd. The control voltage is 1.65V ±1.65V with a tuning sensitivity of +25ppm/V typical and linearity of ±5% max. Supply pushing is 1.2ppm/V typical. The device is designed for 15pF output load and has an input impedance of 51 kΩ.</p>

<p>The Crystek 016876 is a MHz crystal designed for surface mount applications. It operates at a frequency of 13.0625 MHz in fundamental mode, making it suitable for timing and frequency reference circuits.</p><p>&nbsp;</p><p>This crystal is packaged in a surface mount configuration, enabling automated assembly and space-efficient designs. It is RoHS3 compliant and has an MSL of 1 (unlimited), though these compliance claims are unverified.</p><p>&nbsp;</p><p>The part is commonly used in RF and wireless systems, as indicated by its listing in Crystek's chipset crystal catalog for Atmel and Maxim RF transceivers.</p>

<p>The Crystek CVCO55CT-0902-0928 is a voltage controlled oscillator (VCO) covering the 902 MHz to 928 MHz frequency band with a center frequency of 915 MHz. It provides a typical output power of +10 dBm and operates from a 12V supply with a maximum current of 25 mA.</p><p>&nbsp;</p><p>The VCO tunes from 0.3V to 4.7V with a typical tuning sensitivity of 10 MHz/V. It exhibits typical phase noise of -110 dBc/Hz at 10 kHz offset and -132 dBc/Hz at 100 kHz offset. Second harmonic suppression is -20 dBc typical.</p><p>&nbsp;</p><p>The device is housed in a surface-mount 16-QFN package measuring 12.70 mm x 12.70 mm x 3.81 mm. It supports an operating temperature range of -40°C to +85°C and is available in tape and reel packaging.</p>

<p>The CVCO55BE-1350-1400 is a voltage controlled oscillator (VCO) from Crystek Corporation. It operates over a frequency range of 1350 to 1400 MHz with a center frequency of 1375 MHz. The tuning voltage range is 0.5 V to 4.5 V, and it requires a 5 V supply voltage.</p><p>&nbsp;</p><p>Electrical characteristics include a typical output power of 7 dBm with a maximum supply current of 35 mA. Harmonic suppression for the 2nd harmonic is -15 dBc typical. Phase noise is -126 dBc/Hz at both 10 kHz and 100 kHz offsets. Pushing is 3 MHz/V maximum, and tuning sensitivity is 3 MHz/V typical. The load impedance is 50 Ω.</p><p>&nbsp;</p><p>The VCO is housed in a 16-QFN surface mount package measuring 12.70 mm x 12.70 mm x 3.81 mm. Operating temperature range is -40°C to 85°C, storage temperature -45°C to 90°C. It is RoHS3 compliant (unverified) and has MSL 1 rating.</p>

<p>The Crystek CVCO55BE-0400-0800 is a voltage controlled oscillator (VCO) designed for applications requiring a 600 MHz center frequency. It covers a frequency range of 400 MHz to 800 MHz with a tuning voltage of 0 V to 12 V. The VCO operates from a 5 V supply and draws a maximum of 17 mA. Its typical output power is 7 dBm with a ±5 dBm tolerance. Phase noise is specified at -105 dBc/Hz (offset not specified). The second harmonic is typically -5 dBc, and pushing is 5 MHz/V. This VCO is housed in a 16-QFN surface mount package measuring 12.70 mm x 12.70 mm with a height of 3.81 mm. It operates over a temperature range of -10°C to 70°C. The device is RoHS3 compliant (unverified) and has MSL Level 1. Applications include wireless infrastructure, test equipment, and other RF systems requiring a stable, tunable oscillator.</p>

<p>The Crystek CCHD-950-50-80.000 is a high-performance 80 MHz XO (Standard) crystal oscillator featuring an HCMOS output. It provides ultra-low phase noise with a typical noise floor of -165 dBc/Hz and low phase jitter of 40 fs (12 kHz to 20 MHz). The oscillator operates from a 3.3V supply with a maximum current consumption of 25 mA. Key electrical characteristics include a maximum rise/fall time of 3 ns (20% to 80% Vdd), a symmetry (duty cycle) of 45/55% maximum at 50% Vdd, and an output load of 15 pF. The device offers a frequency stability of ±50 ppm and an aging rate of less than 3 ppm in the first year and less than 1 ppm thereafter.</p><p>&nbsp;</p><p>Designed for applications requiring low phase noise and jitter, this oscillator is suitable for High Definition TV, avionics low phase signal sources, and test and measurement equipment. The component is housed in a surface mount 4-SMD, No Lead package measuring 14.20 mm x 9.14 mm with a seated height of 5.30 mm. The pad finish is Immersion Gold (ENIG) with 5 micro inches maximum thickness, ensuring reliable solderability. The operating temperature range is 0°C to 70°C.</p>

<p>This RG174 coaxial cable assembly from Crystek Corporation (part CCSMA2-MM-RG174-12) features SMA male right angle plugs on both ends, with a cable length of 12.00 inches (304.80 mm). The cable is RG174 type with a characteristic impedance of 50 Ohms, making it suitable for RF interconnects. The assembly includes a center conductor of 26 AWG bare copper covered steel, polyethylene insulation, and a black PVC jacket. Shielding is provided by a tinned copper braid with 90% coverage. Strain relief is achieved through adhesive shrink tubing over the crimp area.</p><p>&nbsp;</p><p>The connectors are SMA male plugs with right angle orientation, both rated for free hanging (in-line) mounting. The operating temperature range is -40°C to +85°C, allowing use in a variety of environments. This cable assembly is commonly used in RF test setups, antenna connections, and wireless communication equipment where a flexible and reliable 50 Ohm coaxial link is required.</p>

<p>The Crystek CVCO55BE-1600-2700 is a voltage controlled oscillator designed for applications requiring a 1600 MHz to 2700 MHz frequency range with a center frequency of 2150 MHz. It operates from a 10V supply drawing 22 mA and delivers an output power of 5±5 dBm. Tuning voltage ranges from 1V to 20V with a tuning sensitivity of 5.0 to 7.0 MHz/V. Phase noise is -97 dBc/Hz at 10 kHz offset and -114 dBc/Hz at 100 kHz offset typical. Second harmonic suppression is -15 dBc typical. Pushing is 5 MHz/V and pulling is 10 MHz (all phases).</p><p>&nbsp;</p><p>The VCO is housed in a 16-QFN package measuring 12.70 mm by 12.70 mm with a height of 3.81 mm. It operates over -40°C to +85°C and is supplied in tape and reel packaging. Load impedance is 50 Ω with an input capacitance of 100 pF.</p>

<p>The Crystek Corporation 601252 is a crystal-based oscillator providing a nominal frequency of 98.304 MHz with a frequency stability of ±50ppm. It operates from a 1.8V supply voltage, making it suitable for low-voltage applications.</p><p>&nbsp;</p><p>This oscillator is housed in a compact 4-SMD, no lead package measuring 7.20mm x 5.02mm x 1.80mm, designed for surface mount assembly. The operating temperature range spans -40°C to 85°C, allowing use in a variety of environments.</p><p>&nbsp;</p><p>Typical applications include timing and clock generation in telecommunications, networking, and industrial electronics where precise frequency control is required. The crystal base resonator ensures reliable performance and low jitter.</p>

<p>The Crystek 601107 is a crystal oscillator designed for precise timing applications. It operates at a frequency of 98.304 MHz with a frequency stability of ±50ppm, ensuring reliable performance in demanding environments. The oscillator is based on a crystal resonator and requires a supply voltage of 3.3V.</p><p>&nbsp;</p><p>The device is housed in a surface mount package measuring 7.00mm x 5.00mm, making it suitable for compact PCB designs. It operates over a temperature range of 0°C to 70°C, covering standard commercial applications.</p><p>&nbsp;</p><p>This oscillator is commonly used in telecommunications, networking, and industrial control systems where accurate clock signals are essential. Its surface mount package facilitates automated assembly and reduces board space requirements.</p>

<p>The Crystek CCPD-034-50-200.000 is a surface-mount crystal oscillator (XO) that provides a precise 200 MHz output clock signal. It uses a crystal base resonator and delivers LVPECL logic levels, making it suitable for high-speed digital systems requiring low jitter and fast edge rates.</p><p>&nbsp;</p><p>Key electrical specifications include a nominal supply voltage of 3.3V, a supply current of 88mA, and a frequency stability of ±50ppm over the operating temperature range of 0°C to 70°C. The oscillator features an enable/disable function for power management.</p><p>&nbsp;</p><p>The device is housed in a compact 6-SMD, No Lead package measuring 7.00mm x 5.00mm with a height of 1.80mm, designed for automated surface-mount assembly. It is RoHS3 compliant and has an MSL rating of 1 (unlimited).</p>

<p>The Crystek CVPD-940-74.1758 is a Voltage Controlled Crystal Oscillator (VCXO) that uses a quartz crystal as its base resonator. It outputs a precise 74.1758 MHz frequency with LVPECL logic levels. The device operates from a 3.3V supply voltage and draws 88mA typical current. The absolute pull range (APR) is ±50ppm, allowing fine frequency adjustment via an external control voltage. An enable/disable function provides output control for power management. The oscillator is housed in a 6-SMD, no-lead surface mount package measuring 14.20mm x 9.14mm with a height of 5.30mm. Its operating temperature range is 0°C to 70°C, suitable for commercial applications. The component is RoHS3 compliant and has a moisture sensitivity level (MSL) of 1, indicating unlimited floor life before soldering.</p>

<p>This oscillator from Crystek Corporation is a crystal-based XO (standard) oscillator with a nominal frequency of 156.25 MHz. The output logic is LVPECL, requiring a 3.3V supply voltage and drawing a typical current of 88mA. It features an enable/disable function for power control. Frequency stability is specified at ±50ppm maximum over the full operating temperature range of -40°C to 85°C.</p><p>&nbsp;</p><p>The oscillator is housed in a surface mount 6-SMD, No Lead package with dimensions of 7.00mm x 5.00mm x 1.80mm. It is suitable for applications requiring a precise 156.25 MHz clock signal with LVPECL logic levels, such as high-speed networking, telecommunications, and data communications.</p><p>&nbsp;</p><p>Environmental compliance includes RoHS3 (verified from existing_db, low confidence), REACH Unaffected, and MSL Level 1 (Unlimited). The part is designed for reliable operation in industrial temperature ranges.</p>

<p>The CCO-083-100.000 is a 100 MHz crystal oscillator (XO) from Crystek Corporation, designed to provide a precision sine wave output. Operating at 3.3V with a supply current of 15mA, it offers a frequency stability of ±25ppm over a temperature range of 0°C to 70°C. This oscillator is built with a crystal base resonator, ensuring reliable frequency generation. The device comes in a through-hole 14-DIP package (full size, metal can) with 4 leads, measuring 20.83mm in length, 13.21mm in width, and 7.62mm in height. It is suitable for general-purpose clock generation and timing applications where a stable 100 MHz sine wave reference is required.</p>

<p>The CVCO55BE-2300-2450 is a voltage controlled oscillator (VCO) from Crystek Corporation designed for applications requiring a 2375 MHz center frequency. It operates over a frequency range of 2300 to 2450 MHz with a tuning voltage of 0.5 to 4.5 V. The oscillator delivers a typical output power of 4 dBm and exhibits a phase noise of -100 dBc (offset not specified). Second harmonic suppression is -15 dBc typical. The device requires a 5 V supply and draws a maximum current of 29 mA. It is housed in a 16-QFN package measuring 12.70 mm x 12.70 mm x 3.81 mm, suitable for surface mount assembly. Operating temperature range is -40°C to +85°C. The part is RoHS3 compliant and has an MSL rating of 1 (unlimited).</p>

<p>The CCO-083-200.000 is a crystal oscillator (XO) from Crystek Corporation, designed to provide a stable 200 MHz sine wave output. This through hole component operates from a 3.3V supply voltage with a typical current consumption of 15 mA. It offers a frequency stability of ±25 ppm over the 0°C to +70°C operating temperature range, making it suitable for general purpose applications. The oscillator is housed in a 14-DIP metal can package with 4 leads, measuring 20.83 mm x 13.21 mm x 7.62 mm. It is RoHS3 compliant and has an MSL of 1 for unlimited floor life. The package is designed for through hole mounting, providing reliable mechanical stability in various electronic assemblies.</p>